Forms high strength conductive bonds

This two part silver epoxy offers high electrical conductivity and strong conductive bonding. Use in place of traditional soldering on heat sensitive components. Good for repairing defective traces and creating jumpers on boards. Can be used as an effective heat sink adhesive. This Conductive Silver Epoxy comes in two 7g syringes.

 Frequently Asked Questions on this product

This epoxy adhesive can adheres not only on most of the metal surfaces (aluminium, bronze, brass, copper, steel etc.) but it can also well adheres on glass, wood, plastic, paper, fiber & rubber surfaces as well.

Specifications

Specification Test Method Result Mechanical Properties Tensile Strength ASTM-D-638-02A 911 psi Elongation ASTM-D-638-02A 0.3 % Compressive Strength ASTM-D-695-02A 1100 psi Flexural Strength ASTM-D-790-03 2,500 psi Shear Strength ASTM-D-732-02 234 psi Cantilever Beam (IZOD) Impact ASTM-D-256-02 E1 0.39 ft lb ft / in Electrical Properties Volume Resistivity @ 25°C MIL-STD-883E Notice 3, method 5011.4, paragraphs 3.5.8, 3.8.11.1 (Covered Under A2LA Accreditiation) 0.18 ohm · cm Electrical Resistance (in ohms)     Sample Size   3mm x 3mm x 1mm Base Material   Plastic cap Results:     Uncured Material   no reading Heat Cured (at 65°C for 15 minutes)   0.8 ohms Air Cured (at room temp. for 5 hours)   0.2 ohms Electrical Resistance (in ohms)     Sample Size   30mm x 25mm x 1mm Base Material   Fiber glass epoxy Results:     Uncured Material   no reading Heat Cured (at 65°C for 15 minutes)   2.5 ohms Air Cured (at room temp. for 5 hours)   4.0 - 6.0 ohms Thermal Properties Thermal Conductivity ASTM E 1461 in W/m·K (BTU in /(hr ft2  F) ) 25°C   0.903 (6.27) 50°C   0.893 (6.20) 100°C   0.813 (5.64) Glass Transition Temperature (Tg) ASTM D 3418 55.1 °C [131 °F] CTE prior Tg ASTM E 831 38.5 ppm/°C CTE after Tg ASTM E 831 101.8 ppm/°C Cure Schedule Air Cure @ 24°C (75°F)   5 hours Heat Cure: 65°C / 149°F 90°C / 194°F 125°C / 257°F 150°C / 302°F   15 minutes 12 minutes 7 minutes 5 minutes Working Time @ 22°C   10 minutes Minimum Operating Temp.   < -55 °C (-67 °F) Maximum Operating Temp.   150 °C ( 302 °F ) General Specifications Mixing Ratio   1:1 Density ASTM-D-256-02 E1 2.34 g/cm3 Color (cured material)   Silver Grey

Outgassing Properties (ASTM E595) Cure Time % TML (Total Mass Loss) % WVR (Water Vapor Regain) %CVCM (Collected Volatile Condensable Material) 10 min@65°C + 24 hours@23°C 7.16 0.06 0.1 10 min@65°C + 48 hours@23°C 6.11 0.05 0.05

Available Sizes

Catalog Number Sizes Available Description 8331-14G 14 g (0.35 oz) Two 7g syringes, 3mL each 8331-40G 40 g (1.4 oz) jar 8331-454G 454 g (1 lb) 1 lb kit